Are you looking for details about Installing A Bathtub?
Mounting a bathtub isn't exactly brain surgery, yet it does require strong plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old bathtub with a new one is likewise a reasonably difficult job. If the old bathtub is readily available, the job can relocate easily; if you have to open up a wall to eliminate the old bathtub and also place the new bath tub, the job is a lot harder. In either situation, the job is within a house handyman's skills, although you will need an assistant to leave the old bathtub and also embeded in the new one. See to it you have actually qualified on your own for the task and are comfortable trying it. Instead of hiring a specialist to take control of a halfway-completed job, it is much better to consider utilizing one before you start. Chances are you may require a professional plumber to make tube links.
This short article will certainly assist you set up a new bathtub in your shower room if you have already purchased a new bathtub as well as don't require to transform the plan of your previous water system pipes.
Your devices and product checklist should comprise the following:
Preparing for the Installation
First of all, the sustaining framework supplied with the bath should be fitted (if called for) according to the producer's directions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is important to make sure that if the faucet comes with a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the faucets device to prevent strain on the bathtub.
Fit the flexible tap connectors to the bottom of the two faucets making use of 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make sure you utilize all of the supplied washers.
Link the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath should currently be ready to be suited its last setting.
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installation, then the first thing you need to do is separate the water system. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The process of removing the existing faucets can be fairly problematic as a result of the limited accessibility that is often the case.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the taps. Have a cloth ready for the continuing to be water that will come from the pipelines. When the supply pipelines have actually been gotten rid of, use the same device to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the single taps from turning during this procedure. As soon as the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old securing compound.
Before proceeding to fit the new faucets, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the brand-new faucets, then a shank adapter is needed for the new taps to fit.
Mounting the Bathtub
Utilizing the two wood boards under its feet, place the bathtub in the required setting. The wooden boards are handy in evenly spreading the weight of the bathtub over the location of the boards instead of focusing all the weight onto 4 small points.
The following objective is to make certain that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level and readjusting the feet on the bath tub up until the spirit level checks out degree.
To mount faucets, fit all-time low of the outermost adaptable faucet adapter to the ideal supply pipe by making a compression join; then do the same for the other tap.
Turn on the water and also examine all joints as well as new pipework for leaks and also tighten them if required. Load the bath tub as well as also inspect the overflow electrical outlet and the regular electrical outlet for leaks.
Lastly, repair the bathroom paneling as described in the maker's user's manual. Tiling and securing around the bath tub should wait until the tub has actually been made use of at least once as this will resolve it right into its last placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end supplies a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly require decreasing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, position the faucet in the installing opening in the bath/basin making certain that the washers remain in place in between the tap and also the sink. Secure the faucet in place with the producer offered backnut. As soon as the tap is securely in place, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with typical faucet adapters. The former kind must be connected to the tap ends first, tightening up just by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the area where the bathroom meets the ceramic tile, it is needed to seal the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to split an inflexible seal, causing the water to penetrate the wall between the bath as well as the tiling, bring about problems with dampness and possible leakages to the ceiling below.
You can pick from a range of coloured sealers to assimilate your fixtures and installations. They are sold in tubes and also cartridges, as well as can securing gaps approximately a width of 3mm (1/8 inch). If you have a larger void to load, you can load it with spins of soaked newspaper or soft rope. Bear in mind to always fill the bathtub with water before sealing, to allow for the activity experienced when the bathtub remains in use. The sealant can fracture rather early if you do not consider this movement before sealing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also easily available on the market. It is recommended to fit the tiles using waterproof or waterproof glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
I ran across that post about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround when doing research the web. For those who appreciated our article please be sure to share it. I appreciate reading our article about A Step-by-Step Guide to Installing a Bathtub.
Excellence awaits, dial!